To check tyre tread, measure the depth of the main grooves with a tread depth gauge at several points around the tyre, inside the middle three-quarters of its width. On a car the law asks for at least 1.6 mm across that central band and all the way round the tyre. Anything close to that figure is a tyre you’ll be paying to replace soon, and anything under it is illegal to drive on.
That rule comes from regulation 27 of the 1986 Road Vehicles (Construction and Use) Regulations and is repeated in Annex 6 of the Highway Code. We checked both at source on 20 Nov 2026, the regulation on legislation.gov.uk and the code on GOV.UK. The rest of this page covers how to measure properly, what the MOT tester looks at, and how to read the tyres on a used car you’re thinking of buying.
What is the legal tyre tread depth in the UK?
The limit depends on the vehicle. Regulation 27(4) sets 1.6 mm for passenger vehicles with no more than eight passenger seats, goods vehicles up to 3,500 kg and light trailers. The Highway Code gives the same figure for cars, light vans and light trailers, and a lower one for bikes and heavy vehicles.
| Vehicle | Minimum depth | Where it is measured | Source |
|---|---|---|---|
| Cars, light vans (up to 3,500 kg), light trailers | 1.6 mm | A continuous band over the middle three-quarters of the tread width, all the way round | Reg 27(4)(f), Construction and Use Regulations 1986 |
| Motorcycles, large vehicles, passenger-carrying vehicles | 1 mm | Three-quarters of the tread breadth, in a continuous band all the way round | Highway Code, Annex 6 |
| Mopeds | Visible tread | Across the tyre | Highway Code, Annex 6 |
Depth isn’t the only test. The same regulation bans a cut longer than 25 mm or 10% of the tyre’s section width (whichever is greater), any lump, bulge or tear caused by the structure failing, and exposed ply or cord. A tyre can have plenty of tread and still be illegal because of a bulge in the sidewall.
How do you measure tyre tread depth with a gauge?
A gauge costs little at any motor factor and gives a reading in millimetres, which no coin or rule of thumb can. Here’s the method that matches the way the law is written.
- Park on level ground with the wheels straight. For the front tyres, turn the steering to full lock afterwards so you can reach the inner shoulder, where wear hides.
- Find the primary grooves. These are the deep channels running round the tyre. The DVSA MOT inspection manual treats grooves that hold the tread wear indicators, or were cut as deep as them when new, as primary. Thin cuts called sipes don’t count.
- Push the gauge probe into the groove until the flat base sits on the tread blocks either side, then read it.
- Take readings in the inner, middle and outer grooves that fall inside the central three-quarters of the width.
- Repeat at three or four places round the tyre. Roll the car a short way if you need to. The 1.6 mm has to hold around the whole circumference, so one good reading proves little.
- Write down the lowest figure for each tyre. That’s the number that matters, for the law and for your budget.
How do you check tyre tread without a gauge?
Look for the tread wear indicators first. They’re small raised bars moulded across the bottom of the main grooves, and many tyres mark their position with a small symbol on the shoulder. Once the tread surface is level with those bars, the tyre has worn down to the limit its maker built in, and you should measure it properly before anyone drives on it.
Coin tests are popular. Treat them as a rough screen, not a measurement: we couldn’t find any official source that gives the width of a coin’s border, so a coin can tell you a tyre looks low but can’t tell you it’s legal. If a tyre looks borderline by eye, it needs a gauge.
What does uneven tyre wear tell you about a car?
This is where tyres earn their place on a buyer’s checklist. Annex 6 of the Highway Code says uneven wear may be caused by faults in the braking or suspension systems or by wheels that are out of alignment. A pattern is a clue to the car, not only to the rubber.
| What you see | Likely cause to ask about | What to do |
|---|---|---|
| Inner or outer shoulder worn, centre fine | Alignment out, often after kerbing or worn suspension parts | Ask for an alignment receipt; budget for tyres and a check |
| Centre worn more than both edges | Run at too high a pressure | Check the pressure placard; usually not a fault in the car |
| Both edges worn, centre fine | Run under-inflated | Ask how often pressures were checked |
| Scalloped or cupped patches | Worn shock absorbers or wheel balance | Do the bounce test below; ask a garage to look |
| One tyre much newer than the other on the same axle | A puncture, a blow-out, or a kerb strike | Ask why; check the wheel rim for damage |
The Highway Code’s bounce test is simple: push down hard on one corner of the car. If it keeps bouncing after you let go, the shock absorbers are worn. Worn dampers chew tyres, so the two problems often turn up together.
Will a car fail its MOT because of the tyres?
Yes, and the tester’s categories are strict. In the DVSA MOT inspection manual for cars, tread depth below the legal requirement is a dangerous defect. So is a lump, bulge or tear caused by the tyre’s structure failing. A cut deep enough to reach the ply or cords is major, and so is fitting tyres of different sizes or different structure on the same axle.
Tyres are a big part of what testers find. In the DVSA’s 2025-26 MOT data for class 3 and 4 vehicles (mostly cars and light vans; data set updated 10 Sep 2026), a tyre defect was recorded on 6.23% of the 33,310,534 tests, and tyres made up 60.60% of the dangerous defects. A dangerous defect matters after the test too: GOV.UK says driving a car with one risks a ban, 3 points and a fine as high as £2,500 (GOV.UK, read 14 Nov 2026).
How do you check the tyres on a used car before you buy?
You can learn a lot before you travel. The DVSA MOT history lists every advisory the tester wrote, and tyre wording is common: a front tyre “worn close to legal limit”, a sidewall “slightly damaged”, tyres “perished” with age. Run the reg through our MOT history check and read the last two tests. An advisory a year ago on a car that has covered thousands of miles since is a tyre that’s probably now at the limit.
At the viewing, work round all four corners:
- Measure each tyre with a gauge and note the lowest reading.
- Check that both tyres on each axle are the same size. The size is the code on the sidewall, such as 205/55 R16.
- Run a hand along each sidewall, outside and in, feeling for bulges or cuts.
- Find the date marking. The Highway Code says it must always be legible; if it’s been scuffed off, ask why.
- Look at the spare or the repair kit, and that the locking wheel nut key is in the car.
Low tread isn’t a reason to walk away from a good car. It’s a running cost you can put a figure on and raise with the seller. Our guide to how to test drive a car covers what a worn or mismatched tyre feels like on the road.
Checks to run on the car as well as the tyres
Tyres tell you about the last few thousand miles. The car’s records tell you about the rest of its life. Before you pay, look the registration up with these checks:
- A car check by registration, to match the make, model and colour with the car in front of you.
- The mileage check, which compares the odometer readings taken at each MOT.
- A car write off check, since a car that’s been in a crash can wear its tyres unevenly for good.
- The car finance check, so a lender doesn’t own the car you’re paying for.
- Our car spec check, which shows the wheel and tyre size the car left the factory with.
To see the layout of the full report first, open the sample report.
Tyre tread questions
What is the minimum tyre tread depth for a car?
1.6 mm, measured over the middle three-quarters of the tread width and right round the tyre. That’s regulation 27(4) of the Construction and Use Regulations 1986.
How do I check my tyre tread depth at home?
Use a tread depth gauge in the main grooves, at three or four places round each tyre, and keep the lowest reading. Turn the front wheels to full lock to reach the inner edge.
Can the outer edge of a tyre be bald and still pass the MOT?
The MOT inspection manual measures only the central three-quarters, so the outer strips aren’t part of the depth test. A bald edge is still a sign of an alignment or pressure problem worth fixing.
What do the tread wear indicators mean?
They’re raised bars in the bottom of the main grooves. When the tread is level with them the tyre has reached its built-in wear limit, so measure it and plan a replacement.
Is the tread depth rule different for vans and motorbikes?
Light vans up to 3,500 kg follow the car rule of 1.6 mm. Motorcycles and large vehicles need at least 1 mm, and mopeds need visible tread, according to the Highway Code.
Can I have two different tyres on the same axle?
The MOT manual doesn’t list a brand mismatch as a defect. Different sizes or different structures on one axle are a major defect, so keep each axle’s pair matched.
Does the MOT history show tyre problems?
Often, yes. Testers write tyre advisories such as wear close to the limit or sidewall damage, and they appear in the free MOT history for that registration.